EMC Certification Of Automatic Ethanol Fireplace

             EMC test report of xsfireplaces' automatic ethanol fireplace 

 

Test standard as follow: 

EN 55014-1:2006+A1:2009+A2:2011, EN 55014-2:2015 EN61000-3-2:2014,EN 61000-3-3:2013

(Council Directive 2014/30/EU on Electromagnetic Compatibility)

EMC MEASUREMENT AND TEST REPORT

 

Test model: RCFB6000 automatic ethanol fireplace

GENERAL INFORMATION

Product Description for Equipment Under Test (EUT)

The product that is produced by xsfireplace (sell-fire) Application model RCFB6000 or the "EUT" as referred to in this report is Intelligent Ethanol Fireplace. RCFB4500, RCFB6000, RCFB7600, RCFB9000, RCFB10K, RCFB12K, RCFB15K, RCFB18K, RCFB21K are family products. Complete test was conducted on RCFB6000.

 

In order to meet the EMC requirements approved by CENELEC, the following standards will be cited:

1. EN 61000-3-2: 2014, EMC-Limits-Limits for the harmonic current emissions (equipment input current up to and including 16 A per phase).

2. EN 61000-3-3: 2013 ,EMC-Limits-Limitation of voltage changes, voltage fluctuations and flicker in public low-

voltage supply systems, for equipment with rated current≤16 A per phase and not subject to conditional connection.

3. EN 55014-1:2006+A1:2009+A2:2011, Electromagnetic compatibility-Requirements for household appliances, electric tools and similar apparatus-Emission.

4. EN 55014-2: 2015, Electromagnetic compatibility-Requirement for household appliances, electric tools and similar apparatus-Immunity-Product family standard.

The following satandares were also be cited in:

EN61000-4-2:2009,EN61000-4-4:2012, EN61000-4-5:2006,EN61000-4-6:2014,EN61000-4-11:2004

Note: The test data is only valid for the test sample. There is possible deviation from the original test data for other products

Equipment Modifications

No modification to the EUT were made by China Ceprei (Sichuan) Laboratory to make sure the EUT comply with applicable limits.

 

Test equapment list and  Detail as  follow: 

1.3 Test procedure and the test set-up
Procedure
a. The EUT was placed on the top of a wooden table 0.8 meters above the ground and operated to produce the
maxim um harmonic components under normal operating conditions for each successive harmonic component inturn.
b. The class ification of EUT is according to section 5 ofEN 61000-3-2. The EUT is classified as follows.
Class A: Balanced three -phase equipment, Household appliances excluding equipment as Class D, Tools
excluding portable tools, Dimmers for incandescent lamps, audio equipment, equipment not
specified in one of the three other classes.
Class B: Portable tools. Are welding equipment which is not professional equipment
Class C:Lighting equipment, including dimming devices.
Class D: Equipment having a specified power less than or equal to 600 W of the following types: Personal
computers and personal computer monitors.
e. The corespondent test program of test instrument to measure the current harmonics emanated from EU'T is
chosen. The measure time shall be not less than the time necessary for the EU'T to be exercised.

 

Test data as follow:

3.3.2 Test Procedure
The EUT was placed on a turn table. The turn table can rotate 360 degrees to determine the position of the
maximum emission level. EU'T was set 3 meter (Semi-Anechoic Chamber) away from the receiving antenna which
was mounted on a antenna tower, The antenna can move up and down between l to 4 meters to find out the
maximum emission level. Broadband antenna (calibrated biconical and log periodical antenna) were used as a
receiving antenna, Both horizontal and vertical polarization of the antenna were set on measurement.
The bandwidth ofthe R&S EMl Receiver ESU40 was set at 120 kHz.
The frequency range from 30MHz to 1000MHz was pre-scanned with a peak detector.
The all final readines from test receiver were measured with Ouasi-Peak detector

 

Test equipment list  and detail :

 

Test model and process  as follow: